Content Source: 2021 Indian Scout Bobber Owner’s Manual (9931589 R02) > Features and Controls Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Multi-Function Display Modes

With the ignition switch on, use the right-hand trigger switch to toggle through the modes of the multi-function display and to change settings in the display.
The following display modes are available:
  • Odometer
  • Trip Odometer
  • Engine Speed
  • Gear Indicator
  • Battery Voltage
  • Engine Error Codes
  • Engine Temperature

Odometer

The odometer displays total distance traveled.

Trip Odometer

The trip odometer displays total distance traveled since being reset. To reset, toggle to the trip odometer, then press and hold the MODE button until the trip odometer resets to zero.

Engine Speed

Engine speed displays in revolutions per minute (RPM).

Gear Indicator

The vehicle’s current gear position is displayed on the MFD.

Battery Voltage

Battery voltage displays real-time, regulated charge voltage supplied to the battery. The voltage level may fluctuate depending on electrical load and engine RPM.

Display Units (Standard/Metric)

The display can be changed to display either standard or metric units of measurement.
  Standard Display Metric Display
Distance Miles Kilometers
Temperature Fahrenheit Celsius
Time 12-Hour Clock 24-Hour Clock
  1. Turn the ignition off.
  2. Wait 10 seconds.
  3. Press and hold the right-hand trigger switch while turning the key to the ON or PARK position.
  4. When the display flashes the distance setting, tap the right-hand trigger switch to advance to the desired setting.
  5. Press and hold the right-hand trigger switch to save the setting and advance to the next display option.
  6. Repeat the procedure to change remaining display settings.

Clock

NOTICE
The clock must be reset any time the battery has been disconnected or discharged.
  1. Use the right-hand trigger switch to toggle to the odometer display.
  2. Press and hold the right-hand trigger switch until the hour segment flashes. Release the switch.
  3. With the segment flashing, tap the right-hand trigger switch to advance to the desired setting.
  4. Press and hold the right-hand trigger switch until the next segment flashes. Release the switch.
  5. Repeat steps 3–4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.

Engine Error Codes

The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes display only during the current ignition cycle. When the ignition switch is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.
If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display.
  1. If the error codes are not displayed, use the right-hand trigger switch to toggle until “Ck ENG” displays on the main line of the display.
  2. Press and hold the right-hand trigger switch to enter the diagnostics code menu.
  3. Record the three numbers displayed in the gear position, clock and odometer displays.
  4. See an authorized dealer for code details and diagnosis.
Image
  • Error Code Number (0–9)
  • Suspect Parameter Number (SPN)
  • Failure Mode Indicator (FMI)

Diagnostic Functionality

Certain conditions will cause the battery indicator to illuminate and an error message to display in the screen. If this occurs, please see your authorized dealer.
Message Location Indicates
LO DC Voltage Screen Voltage remains below 11.0 volts for more than 10 seconds
OV DC Voltage Screen Voltage remains above 15.0 volts for more than 10 seconds
ERROR All Checksum error (gauge malfunction)

Over Temperature Display and Warning Indicator

If the engine coolant temperature approaches unsafe operating conditions while the engine is running, the engine overheat indicator will illuminate and the current engine coolant temperature will display on the MFD. Stop the engine as soon as safely possible. Check the coolant level. Check the radiator for debris. Check cooling fan operation. If the warning continues to display after restarting the engine, stop the engine immediately

© Copyright Polaris Inc. All rights reserved.