Suspension System

Content Source: 2021 RZR XP Turbo S Velocity / XP Turbo S4 Velocity Owner’s Manual (9931525 R02) > Maintenance Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Suspension System

Shock Adjustment Recommendations

WARNING

Be advised that the shocks contain nitrogen at high pressure. Damaged shocks could cause injury if not replaced or addressed promptly by qualified personnel.

Shock Adjustments
RZR XP Turbo S and Turbo S Velocity
Weight Condition assuming each rider, wearing gear, is 215 lbs. (97.5 kg)		Spring Preload Adjustment
Riders	Cargo + Accessories	Shaded cells indicate factory settings
Driver only	0	Remove 0.2 inch (5 mm) preload, front and rear
Driver + 1	0	Factory default preload
Driver + 1	100 lbs. (45 kg)	Add 0.2 inch (5 mm) preload, front and rear
Driver + 1	200 lbs. (91 kg)	Add 0.4 inch (10 mm) preload, front and rear
Driver + 1	300 lbs. (136 kg)	Add 0.6 inch (15 mm) preload, front and rear

Shock Adjustments
RZR XP 4 Turbo S and 4 Turbo S Velocity
Weight Condition assuming each rider, wearing gear, is 215 lbs. (97.5 kg)		Spring Preload Adjustment
Riders	Cargo + Accessories	Shaded cells indicate factory settings
Driver only	0	Remove 0.4 inch (10 mm) preload, front and rear
Driver + 2	40 lbs. 18 kg	Factory default preload
Driver + 3	40 lbs. 18 kg	Add 0.4 inch (10 mm) preload, front and rear

Front / Rear Spring Preload Adjustment

Elevate the vehicle to allow the suspension to fully extend.
Turn the adjusting ring to the left to add preload. Turn the adjusting ring to the right to remove preload. If equipped, apply the locking ring when desired preload is adjusted.

WARNING

Uneven adjustment may cause poor handling of the vehicle, which could result in an accident. Always adjust both the left and right spring preloads equally or have your POLARIS dealer or qualified person perform the adjustments.

DYNAMIX Shocks
Front Shock Preload Measurement Rear Shock Preload Measurement

DYNAMIX Shocks

Front Shock Preload Measurement

Rear Shock Preload Measurement

Factory Default Preload Settings

Factory Default Preload Settings
RZR XP Turbo S	DYNAMIX
	Front	2.88 inches (7.32 cm)
	Rear	6.38 inches (16.21 cm)
RZR XP 4 Turbo S	DYNAMIX
	Front	2.50 inches (6.35 cm)
	Rear	6.50 inches (16.51 cm)
RZR XP Turbo S Velocity	NON-DYNAMIX
	Front	0.84 inches (2.13 cm)
	Rear	0.96 inches (2.44 cm)
RZR XP 4 Turbo S Velocity	NON-DYNAMIX
	Front	0.72 inches (1.83 cm)
	Rear	0.77 inches (1.96 cm)

Front / Rear Shock Compression Adjustment

NOTE

Applies to Velocity models only.

The compression damping clicker knob is located at the top of the shock reservoir.

Turn the clicker clockwise to increase compression damping.
Turn the clicker counter-clockwise to decrease compression damping.

Front

Rear

Shock Compression Settings
Setting		Compression Damping
WALKER	Softest	Full counter-clockwise position (16 clicks)
	Factory	Center position (8 clicks)
	Firmest	Full clockwise position (0 clicks)