Instrument Cluster

Content Source: 2020 RZR S 1000 / S4 1000 Owner’s Manual (9930957 R01) > Features and Controls Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Instrument Cluster

High water pressure may damage components. Wash the vehicle by hand or with a garden hose using mild soap. Do not use alcohol to clean the instrument cluster. Do not allow insect sprays to contact the lens.

	Speedometer
	Indicator Lamps
	Rider Information Center
	MODE Button

Mode Button

The MODE button is located on the instrument cluster. Use the MODE button to toggle through mode options available in the instrument cluster.

Speedometer

The speedometer displays vehicle speed in either miles per hour (MPH) or kilometers per hour (km/h).

Indicator Lamps

Lamp	Indicates	Condition
	Vehicle Speed	When standard mode is selected, speed displays in miles per hour.
	Vehicle Speed	When metric mode is selected, speed displays in kilometers per hour.
	Over Temperature	This lamp illuminates to indicate an overheated engine. If the indicator flashes, the overheating condition remains, and the system will automatically reduce engine power.
	EPS Warning (if equipped)	This indicator illuminates briefly when the key is turned to the ON position. If the light remains on, the EPS system is inoperative. See your POLARIS dealer, or other qualified person, as soon as possible for repair. Continued operation could result in permanent damage to the EPS unit and increased steering effort.
	Brake Failure	This icon will illuminate if the vehicle sensors detect low pressure in the brake hydraulic system.
	High Beam	This lamp illuminates when the headlamp switch is set to high beam.
	Helmet/Seat Belt	This lamp is a reminder to the operator to ensure all riders are wearing helmets and seat belts before operating. The driver’s seat belt is equipped with a seat belt interlock. Vehicle speed will be limited to 24 km/h (15 MPH) if the seat belt is not secured.
	Check Engine	This indicator appears if an EFI-related fault occurs. Do not operate the vehicle if this warning appears. Serious engine damage could result. Your dealer can assist.
	Direction Indicators	A direction indicator flashes when a turn signal is active. Both indicators flash when the hazard signal is active.

Rider Information Center

The rider information center is located in the instrument cluster. All segments will light up for one second at start-up. If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may have shut off to protect the electronic speedometer. If this occurs, your dealer can provide proper diagnosis.

The information center is set to display standard units of measurement and a 12-hour clock at the factory.

	Gear Indicator	This indicator displays gear shifter position. H = High Gear L = Low Gear N = Neutral R = Reverse Gear P = Park - - = Gear Signal Error (or shifter between gears
	Fuel Gauge	The segments of the fuel gauge show the level of fuel in the fuel tank. When the last segment clears, a low fuel warning is activated. All segments including the fuel icon will flash. Refuel immediately. If the fuel icon fails to display, an open or short circuit has occurred in the fuel sensor circuit. See your dealer.
	Information Display Area	This area displays odometer, trip meter, engine hour meter and programmable service hour interval.
	Under/Over Voltage	This warning usually indicates that the vehicle is operating at an RPM too low to keep the battery charged. It may also occur when the engine is at idle and high electrical load (lights, cooling fan, accessories) is applied. Drive at a higher RPM or recharge the battery to clear the warning.
	Clock	The clock displays time in a 12-hour or 24-hour format.
	Service Indicator	A flashing wrench symbol alerts the operator that the preset service interval has been reached. Your dealer can provide scheduled maintenance.
	4x4 Indicator	This indicator illuminates when the 4X4 system is engaged (switch is on 4X4).
	Turf Mode Indicator (if equipped)	This indicator illuminates when the operator unlocks the differential.

Display Units

The display can be changed to display either standard or metric units of measurement.

TIP

To exit the set-up mode at any time, wait 10 seconds. The display automatically exits and returns to the odometer display.

Measurement	Standard	Metric
Distance	Miles	Kilometers
Fuel	U.S. Gallons	Liters, Imperial Gallons
Temperature	Fahrenheit	Celsius
Time	12–Hour Clock	24–Hour Clock

To change the display units, do the following:

Turn the key to the OFF position.
Press and hold the MODE button while turning the key to the ON position.
When the display flashes the distance setting, tap the MODE button to advance to the desired setting.
Press and hold the MODE button to save the setting and advance to the next display option.
Repeat the procedure to change remaining display settings.

Clock Mode

TIP

The clock must be reset any time the battery has been disconnected or discharged.

To set the clock time, do the following:

Turn the key to the ON position. Use the MODE button to toggle to the odometer display.
Press and hold the MODE button until the hour segment flashes. Release the button.
With the segment flashing, tap the MODE button to advance to the desired setting.
Press and hold the MODE button until the next segment flashes. Release the button.
Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.
Turn the key to the OFF position.

Odometer Mode

The odometer records and displays the distance traveled by the vehicle.

Trip Meter Mode

The trip meter records the distance traveled by the vehicle if reset before each trip. To reset, select the trip meter mode. Press and hold the MODE button until the meter resets to zero. In the Rider Information Center, the trip meter display contains a decimal point, but the odometer displays without a decimal point.

Hour Meter Mode

This mode logs the total hours the engine has been in operation.

Tachometer Mode

The engine RPM is displayed digitally.

TIP

Small fluctuations in the RPM from day to day may be normal because of changes in humidity, temperature and elevation.

Programmable Service Interval

When the hours of engine operation equal the programmed service interval setting, the wrench icon will flash for 5 seconds each time the engine is started. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. The service interval is programmed at 50 hours at the factory.

To change the service interval, do the following:

Press the MODE button until remaining service hours display.
Press and hold the MODE button.
When the service hours flash, press and release the MODE button to advance the hours to the desired setting (including OFF). Press and hold the MODE button to set the new service hour interval.

Diagnostic Display Mode

The EFI diagnostic display mode is for informational purposes only. Your POLARIS dealer or qualified person can provide for all major repairs.

The diagnostic mode is accessible only when the check engine warning indicator activates after the key has been turned on. Leave the key on if you want to view the active code (failure code).

The diagnostic mode becomes inaccessible if the key is turned off and on and the warning indicator is no longer active. This allows the determination of persistent as well as intermittent faults.

Inactive codes are stored in the history of the unit.

Engine Error Codes

The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.

If the CHECK ENGINE light illuminates, retrieve the error codes from the display.

Error Code # (0–9)

Suspect Parameter # (SPN)

Failure Mode Indicator (FMI)

If the error codes are not displayed, use the MODE button to toggle until “Ck ENG” displays on the main line of the display.
Press and hold the MODE button to enter the diagnostics code menu.
Record the three numbers displayed in the gear position, clock and odometer displays.
Press the MODE button to advance to the next error code.
Press and hold the MODE button to exit the diagnostics code menu.
Your authorized POLARIS dealer or qualified person can provide code details and diagnosis.