Content Source: 2019 PRO XD Diesel (9930762 Rev 01) > Features and Controls Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Instrument Cluster

Overview

Image
NOTICE
The use of a high pressure washer may damage the instrument cluster. Wash the vehicle by hand or with a garden hose using mild soap. Do not use alcohol to clean the instrument cluster. Do not allow insect sprays to contact the lens. Immediately clean off any gasoline that splashes on the instrument cluster.
Gear Indicator

H = High Gear

L = Low Gear

N = Neutral

R = Reverse Gear

P = Park

-- = Gear Signal Error (or shifter between gears)
Display Area 2 This area displays odometer, trip meter, trip meter 2, voltage, engine temperature, engine hour meter, programmable service hour interval, ground speed, or engine RPM.
Display Area 1 This area displays engine RPM, ground speed, or coolant temperature.
Fuel Gauge The segments of the fuel gauge show the level of fuel in the fuel tank. When the last segment clears, a low fuel warning is activated. All segments including the fuel icon will flash. Refuel immediately.
Service Indicator A flashing wrench symbol alerts the operator that the preset service interval has been reached. Your POLARIS dealer can provide scheduled maintenance. See Service Hours for more information.
Clock The clock displays time in a 12-hour or 24-hour format.
Differential Lock/Turf Mode Indicator (4x2 models only) Segments of the indicator illuminate based on drive mode engaged.

Indicator Lamps

Image
Check Engine
Image
 This lamp illuminates when the ECM detects a Diagnostic Trouble Code in the engine management system. Do not operate the vehicle if this warning appears. Serious engine damage could result. Your authorized POLARIS dealer can assist. This lamp will also illuminate if the vehicle is keyed on but not started; it will turn off once the vehicle is started.
EPS Warning (if equipped)
Image
 This lamp illuminates to indicate that EPS has shut down. EPS shuts down automatically 5 minutes after the engine is turned off if the key remains in the ON position. Turn the key off and on to reset the unit. If the light remains on after starting the engine, the EPS system is inoperative. Your POLARIS dealer can assist.
Engine Hot
Image
 This lamp illuminates to indicate an overheated engine. If the indicator flashes, a severe overheating condition exists and the engine will shut down automatically. The vehicle will not start again until the engine has sufficiently cooled down. Whenever this lamp illuminates, the engine load should be reduced in any way possible to avoid overheating and shutting down the engine.
Low Oil Pressure
Image
 This lamp illuminates if engine oil pressure drops below safe operating pressure. If this lamp illuminates while the engine is running, turn the engine off as soon as safely possible and check the oil level. If the oil level is correct and the lamp remains on after the engine is restarted, turn the engine off immediately.
Seat Belt
Image
 This lamp flashes for several seconds when the key is turned to the ON position. The lamp will keep flashing as long as riders’ seat belts are not connected.
High Beam
Image
 This lamp illuminates when the headlamp switch is set to high beam.
Park Brake Indicator
Image
 This lamp illuminates when the park brake is active.
Glow Plug Indicator
Image
 This lamp illuminates when the glow plugs are active.

Display Area 1

Image
Pressing the MODE button will change the information displayed in Area 1 .

Speed
Image

Engine Temperature
Image

RPM
Image

Ambient Temperature (Optional)
Image

Display Area 2

Image
Toggle the Up/Down buttons to change the information displayed in Area 2 .

Odometer
Image

Engine Temperature
Image

Trip 1
Image

Ambient Temperature (Optional)
Image

Trip 2
Image

RPM
Image

Voltage
Image

Speed
Image

Engine Hours
Image

Service Hours
Image

Options Menu

Image
Press and hold the MODE button to enter the Options Menu.
Options Menu Notes
Diagnostic Codes

Only displays if fault codes are present or stored
Units - Distance

Select MPH or KPH
Units - Temp

Select between °F and °C
Clock

Select between 12H or 24H, and set time
Backlight Color

Select between Blue or Red
Backlight Level

Set backlight brightness level
Service Hours

View/Set Service hours
Exit Menu

Exit

Unit Selection Distance

Image
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Units-Distance” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (MPH or KPH)

    With the correct unit displayed, Press the mode button which will set the unit and return to the Options Menu.

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Unit Selection Temperature

Image
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Units - Temp” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (°F or °C)

    With the correct unit displayed, Press the mode button which will set the unit and return to the Options Menu.

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Clock

Image
  1. Press and hold the MODE button to enter the Options Menu.
NOTICE
“OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  1. Select “Clock” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (12H or 24H)

    With the correct unit displayed, Press the mode button which will set the unit.

    Toggle the Up/Down Buttons to change the units (Cycles Hours)

    With the correct unit displayed, Press the mode button which will set the unit.

    Toggle the Up/Down Buttons to change the units (Cycles 10s of Minutes)

    With the correct unit displayed, Press the mode button which will set the unit.

    Toggle the Up/Down Buttons to change the units (Cycles 1s of Minutes)

    With the correct unit displayed, Press the mode button which will set the unit and return to the Options Menu.

  1. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Back Light Color

Image
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Backlight Color” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (Blue or Red)

    With the correct unit displayed, Press the mode button which will set the unit and return to the Options Menu.

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Back Light Level

Image
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Backlight Level” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (Increase or Decrease Level)

    With the correct unit displayed, Press the mode button which will set the unit and return to the Options Menu.

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Service Hours

Image
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Service Hours” from the Options Menu by pressing the MODE button.

    Reference the image shown above:

    Press the MODE button.

    Toggle the Up/Down Buttons to change the units (0, 5, 10 - 95, 100)

    With the correct unit displayed, press the MODE button, which will set the unit and return you to the Options Menu.

    NOTICE

    To reset service hours after they have counted down to "0.0", reselect the existing setpoint or select a new service hour value.

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Diagnostic Code

Image
NOTICE
Diagnostic Code Screen will show available MIL that has come on during that ignition cycle.
  1. Press and hold the MODE button to enter the Options Menu.
    NOTICE

    “OPTIONS” will display on the screen for 3 seconds before showing first menu item.
  2. Select “Diagnostic Codes” from the Options Menu by pressing the MODE button.

    Toggle the Up/Down Buttons to cycle through Code(s).

    NOTICE

    This option will only be available if a fault code was set or is active during the current ignition key 'on' cycle. Turning off the ignition will clear any save fault codes from the gauge.

    Reference the image shown above:

    Area A will Display FMI (XX)

    Area B will Display SPN (XXXXXX)

    Clock Area will Display Count (XXX)

  3. To exit the Options Menu the user can select Exit Menu function from Options Menu, can hold Mode Button and exit out of Options Menu, or not press any button for 10 seconds, which will exit out of the Options Menu.

Diagnostic Display Code Definitions

Diagnostic Codes

Component

Condition

SPN

FMI

Low oil pressure switch fault

CAN message 65390 Timeout error

100

11

Current below normal or open circuit

100

5

Engine Temperature Sensor

Voltage above normal, or shorted to high source

 110 3

Voltage above normal, or shorted to high source

 110 4

System Power (Battery Potential/Power Input)

 Data valid but below normal operational range - most severe level 168 1

Voltage above normal, or shorted to high source

 168 3

Voltage below normal, or shorted to low source

 168 4
Gear Sensor Signal

Voltage below normal, or shorted to low source

 523 4
Rear Differential Output

Voltage above normal, or shorted to high source

746

 3

Voltage below normal, or shorted to low source

746

 4

Current below normal or open circuit

746

 5
Fan Relay Driver Ckt.

Voltage above normal, or shorted to high source

1071

 3

Voltage below normal, or shorted to low source

1071

 4

Current below normal or open circuit

1071

 5
Fuel Pump Driver Ckt.

Voltage above normal, or shorted to high source

1347

 3

Voltage below normal, or shorted to low source

1347

 4

Current below normal or open circuit

1347

 5
ECU Output Supply Voltage 1

Voltage above normal, or shorted to high source

3597

 3

Voltage below normal, or shorted to low source

3597

 4
ECU Output Supply Voltage 3

Voltage above normal, or shorted to high source

3598

 3

Voltage below normal, or shorted to low source

3598

 4
All Wheel Drive Control Circuit

Voltage above normal, or shorted to high source

520207

 3

Voltage below normal, or shorted to low source

520207

 4

Current below normal or open circuit

520207

 5
Brake failure lamp faults

Voltage above normal, or shorted to high source

520214

 3

Voltage below normal, or shorted to low source

520214

 4

Current below normal or open circuit

520214

 5
Glow Plug Relay Driver Circuit

Voltage above normal, or shorted to high source

520272

 3

Voltage below normal, or shorted to low source

520272

 4

Current below normal or open circuit

520272

 5
Brake switch (1 or 2 indeterminable) Data erratic, intermittent or incorrect 520285 2
Engine Oil Pressure Sensor Data valid but below normal operating range - least severe level 524076 17

© Copyright Polaris Industries Inc. All rights reserved.