Content Source: 2020 RANGER 570 Full-Size Owner’s Manual (9929907 R02) > Features and Controls Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Mode Button

The yellow button located near the instrument cluster is used to toggle through mode options available.

Display Units

The display can be changed to display either standard or metric units of measurement.
TIP
To exit the set-up mode at any time, wait 10 seconds. The display automatically exits and returns to the odometer display.
Measurement Standard Metric
Distance Miles Kilometers
Fuel U.S. Gallons Liters, Imperial Gallons
Temperature Fahrenheit Celsius
Time 12–Hour Clock 24–Hour Clock
To change the display units, do the following:
  1. Turn the key to the OFF position.
  2. Press and hold the MODE button while turning the key to the ON position.
  3. When the display flashes the distance setting, tap the MODE button to advance to the desired setting.
  4. Press and hold the MODE button to save the setting and advance to the next display option.
  5. Repeat the procedure to change remaining display settings.

Clock Mode

TIP
The clock must be reset any time the battery has been disconnected or discharged.
To set the clock time, do the following:
  1. Turn the key to the ON position. Use the MODE button to toggle to the odometer display.
  2. Press and hold the MODE button until the hour segment flashes. Release the button.
  3. With the segment flashing, tap the MODE button to advance to the desired setting.
  4. Press and hold the MODE button until the next segment flashes. Release the button.
  5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.
  6. Turn the key to the OFF position.

Odometer Mode

The odometer records and displays the distance traveled by the vehicle.

Trip Meter Mode

The trip meter records the distance traveled by the vehicle if reset before each trip. To reset, select the trip meter mode. Press and hold the MODE button until the meter resets to zero. In the Rider Information Center, the trip meter display contains a decimal point, but the odometer displays without a decimal point.

Hour Meter Mode

This mode logs the total hours the engine has been in operation.

Tachometer Mode

The engine RPM is displayed digitally.
TIP
Small fluctuations in the RPM from day to day may be normal because of changes in humidity, temperature and elevation.

Programmable Service Interval

When the hours of engine operation equal the programmed service interval setting, the wrench icon will flash for 5 seconds each time the engine is started. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. The service interval is programmed at 50 hours at the factory.
To change the service interval, do the following:
  1. Press the MODE button until remaining service hours display.
  2. Press and hold the MODE button.
  3. When the service hours flash, press and release the MODE button to advance the hours to the desired setting (including OFF). Press and hold the MODE button to set the new service hour interval.

Diagnostic Display Mode

The EFI diagnostic display mode is for informational purposes only. Your POLARIS dealer or qualified person can provide for all major repairs.
The diagnostic mode is accessible only when the check engine warning indicator activates after the key has been turned on. Leave the key on if you want to view the active code (failure code).
The diagnostic mode becomes inaccessible if the key is turned off and on and the warning indicator is no longer active. This allows the determination of persistent as well as intermittent faults.
Inactive codes are stored in the history of the unit.

Engine Error Codes

The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.
If the CHECK ENGINE light illuminates, retrieve the error codes from the display.
  1. If the error codes are not displayed, use the MODE button to toggle until “Ck ENG” displays on the main line of the display.
  2. Press and hold the MODE button to enter the diagnostics code menu.
  3. Record the three numbers displayed in the gear position, clock and odometer displays.
  4. Press the MODE button to advance to the next error code.
  5. Press and hold the MODE button to exit the diagnostics code menu.
  6. Your authorized POLARIS dealer can provide code details and diagnosis.

© Copyright Polaris Industries Inc. All rights reserved.