Multi-Function Display Modes

Content Source: 2019 Indian Scout Bobber Owner’s Manual (9929713 R04) > Features and Controls Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Multi-Function Display Modes

With the ignition switch on, use the MODE button

to toggle through the modes of the multi-function display and to change settings in the display.

Modes Available	Odometer
	Trip Odometer
	Engine Speed
	Engine Coolant Temperature
	Gear Indicator
	Clock
	Battery Voltage

Odometer

The odometer displays total distance traveled.

Trip Odometer

The trip odometer displays total distance traveled since being reset. To reset, toggle to the trip odometer, then press and hold the MODE button until the trip odometer resets to zero.

Engine Speed

Engine speed displays in revolutions per minute (RPM).

Engine Coolant Temperature

The temperature area displays the temperature of the engine coolant.

Gear Indicator

Gear position will display when the transmission is in gear if the motorcycle is moving with the clutch lever released. It will also display when the transmission is in neutral.

Clock

NOTE

The clock must be reset any time the battery has been disconnected or discharged.

Use the MODE button to toggle to the odometer display.
Press and hold the MODE button until the hour segment flashes. Release the switch.
With the segment flashing, tap the MODE button to advance to the desired setting.
Press and hold the MODE button until the next segment flashes. Release the switch.
Repeat steps 3–4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.

Battery Voltage

Battery voltage displays real-time battery voltage (V). This will increase while engine is running, due to the alternator.

Diagnostic Functionality

Certain conditions will cause the battery indicator to illuminate and an error message to display in the screen. If this occurs, please see your authorized dealer.

Message	Location	Indicates
LO	DC Voltage Screen	Voltage remains below 11.0 volts for more than 10 seconds
OV	DC Voltage Screen	Voltage remains above 15.0 volts for more than 10 seconds
ERROR	All	Checksum error (gauge malfunction)

Display Units (Standard/Metric)

The display can be changed to display either standard or metric units of measurement.

	Standard Display	Metric Display
Distance	Miles	Kilometers
Temperature	Fahrenheit	Celsius
Time	12-Hour Clock	24-Hour Clock

Turn the ignition off.
Wait 10 seconds.
Press and hold the MODE button while turning the key to the ON or PARK position.
When the display flashes the distance setting, tap the MODE button to advance to the desired setting.
Press and hold the MODE button to save the setting and advance to the next display option.
Repeat the procedure to change remaining display settings.

Engine Error Codes

The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes display only during the current ignition cycle. When the ignition switch is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.

If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display.

If the error codes are not displayed, use the MODE button to toggle until “Ck ENG” displays on the main line of the display.
Press and hold the MODE button to enter the diagnostics code menu.
Record the three numbers displayed in the gear position, clock and odometer displays.
See an authorized dealer for code details and diagnosis.

Error Code Number (0–9)
Suspect Parameter Number (SPN)
Failure Mode Indicator (FMI)

Over Temperature Display and Warning Indicator

“HOt” displays and the CHECK ENGINE indicator lamp illuminates under the following conditions.

	Condition	Indicates	Action Required
	Engine coolant temperature approaches unsafe operating condition while the engine is running.	Engine coolant temperature is above a safe operating temperature.	Stop the engine as soon as safely possible. Check the coolant level. Check the radiator for debris. Check cooling fan operation. If the warning continues to display after restarting the engine, stop the engine immediately.