Content Source: 2019 RZR XP Turbo S Velocity / XP Turbo S4 Velocity Owner's Manual (9929465 R02) > Maintenance Chapter

IMPORTANT

The Owner's Manual for this vehicle contains warnings, instructions and other information you must read and fully understand before safely riding or performing maintenance on this vehicle.Always follow the warnings and instructions in Owner's Manual.

Click the CONTENTS link above for the Table Of Contents, or download a full PDF of the Owner Manual in the Owner Support area of Polaris.com

Suspension System

Shock Adjustment Recommendations

WARNING
Be advised that the shocks contain nitrogen at high pressure. Damaged shocks could cause injury if not replaced or addressed promptly by qualified personnel.
Shock Adjustments
RZR XP Turbo S and Turbo S Velocity
Weight Condition
assuming each rider, wearing gear, is 215 lbs. (97.5 kg)
Spring Preload Adjustment
Riders Cargo + Accessories Shaded cells indicate factory settings
Driver only 0

Remove 0.2 inch (5 mm) preload, front and rear

Driver + 1 0

Factory default preload

Driver + 1

100 lbs.

(45 kg)

Add 0.2 inch (5 mm) preload, front and rear

Driver + 1

200 lbs.

(91 kg)

Add 0.4 inch (10 mm) preload, front and rear

Driver + 1

300 lbs.

(136 kg)

Add 0.6 inch (15 mm) preload, front and rear

Shock Adjustments
RZR XP 4 Turbo S and 4 Turbo S Velocity
Weight Condition
assuming each rider, wearing gear, is 215 lbs. (97.5 kg)
Spring Preload Adjustment
Riders Cargo + Accessories Shaded cells indicate factory settings
Driver only 0

Remove 0.4 inch (10 mm) preload, front and rear

Driver + 2

40 lbs.

18 kg

Factory default preload

Driver + 3

40 lbs.

18 kg

Add 0.4 inch (10 mm) preload, front and rear

Front / Rear Spring Preload Adjustment

  1. Elevate the vehicle to allow the suspension to fully extend.
  2. Turn the adjusting ring to the left to add preload. Turn the adjusting ring to the right to remove preload. If equipped, apply the locking ring when desired preload is adjusted.
WARNING
Uneven adjustment may cause poor handling of the vehicle, which could result in an accident. Always adjust both the left and right spring preloads equally or have your POLARIS dealer or qualified person perform the adjustments.
DYNAMIX Shocks

Front Shock Preload Measurement

Rear Shock Preload Measurement

Image
Image

Factory Default Preload Settings

Factory Default Preload Settings
RZR XP Turbo S DYNAMIX
Front 2.88 inches (7.32 cm)
Rear 6.38 inches (16.21 cm)
RZR XP 4 Turbo S DYNAMIX
Front 2.50 inches (6.35 cm)
Rear 6.50 inches (16.51 cm)
RZR XP Turbo S Velocity NON-DYNAMIX
Front 0.84 inches (2.13 cm)
Rear 0.96 inches (2.44 cm)
RZR XP 4 Turbo S Velocity NON-DYNAMIX
Front 0.72 inches (1.83 cm)
Rear 0.77 inches (1.96 cm)

Front / Rear Shock Compression Adjustment

NOTE
Applies to Velocity models only.
The compression damping clicker knob is located at the top of the shock reservoir.
  1. Turn the clicker clockwise to increase compression damping.
  2. Turn the clicker counter-clockwise to decrease compression damping.

Front
Image

Rear
Image
Shock Compression Settings
Setting Compression Damping
WALKER Softest

Full counter-clockwise position (16 clicks)

Factory

Center position (8 clicks)

Firmest

Full clockwise position (0 clicks)


© Copyright Polaris Industries Inc. All rights reserved.