The rider information
center is located in the instrument cluster. The center displays vehicle
speed, engine speed, odometer,
resettable trip meters (2), total engine hours of operation,
fuel level, engine temperature, and a diagnostic display mode.
Setting changes must
be made with the engine running or with the vehicle powered by an
external DC power supply connector.
The information center is set to display standard units
of measurement for distance and temperature.
Information
Display Area - This area displays either engine speed or vehicle
speed (whichever is not displayed in the speed display), engine temperature
and maximum vehicle speed.
Speed
Display - The speed display area displays either vehicle speed
or engine speed.
Fuel
Gauge - Not available on all models. The segments of the fuel
gauge show the level of fuel in the fuel tank. When the last segment
clears, a low fuel warning is activated. All segments
including the fuel icon will flash. Refuel immediately.
| NOTE |
| The low fuel indicator and fuel level gauge on the Standard Instrument
Cluster are not supported on models with a fuel level
gauge on the fuel cap. |
| TIP |
| If the fuel icon fails to display, an open or short circuit has occurred
in the fuel sensor circuit. See your dealer. |
Odometer/Engine Hour Display - This area displays the odometer,
Trip A, Trip B and engine hours.
Speed Display Area
The speed display
area displays either vehicle speed or engine speed. Vehicle speed
is displayed in either miles per hour
(MPH) or kilometers per hour (km/h). Engine speed
is displayed in revolutions per minute (RPM).
- To change which item
displays, first make sure the information display area is set to display
either engine speed or vehicle
speed.
- Press and release the center button.
Odometer/Engine Hour Display
Area
This area displays
the odometer, Trip 1 meter, Trip 2 meter, CLOCK, and Engine Hours
meter.
The odometer displays
the total distance traveled by the vehicle since manufacture. Each
trip meter records the distance traveled
by the vehicle on a trip if the meter is reset before
each trip. The CLOCK displays the time, and the engine hour meter
displays
the total hours the engine has been in operation
since manufacture.
To change the display, press and release the SET button
or SET switch until the desired item is displayed.
To reset a trip
meter, press and hold the
SET button or SET switch until the meter resets to zero.
Playback Function
The playback function
allows the rider to record and play back engine speed, vehicle speed
and throttle position sensor information
for up to three minutes.
To Record
- Press and hold the center
button
on the instrument cluster to enter the Options Menu.
- Press and release the MODE button until PLAYBACK
appears in the information display area.
- Press and release the SET button.
RECORD will appear in the information display area.
- To begin recording, Press and release the SET button.
The playback indicator will flash while recording is in progress.
Recording is complete when the light stops flashing.
| NOTE |
| To stop recording at any time during the recording process, press and release the SET button. |
To Playback
- To play back the
recorded data, stop the vehicle and wait for engine speed to drop
below clutch engagement.
- Press and hold the center button
on the instrument cluster to enter the Options Menu.
- Press and release the MODE button until PLAYBACK
appears in the information display area.
- Press and release the SET button twice.
PLAY will appear in the information display area.
- Press and release the SET button to play the recorded
data.
Once playback has concluded, REPLAY will appear in the
information display area.
- Press and release the SET button to REPLAY recorded
data.
- Press and release the MODE button to end playback
and return to the Options Menu.
Standard/Metric Display
The odometer and
temperature displays can be viewed in either standard or metric units
of measurement. Both displays change
if units are changed. The new settings will remain
until changed by the operator.
Change Method 1
- Press and hold the center button
on the instrument cluster to enter the Options Menu.
- Press and release the MODE button until engine
temperature appears in the information display area.
- Press and release the SET button or SET switch
to change units.
Change Method 2
- Press and release the SET button or SET switch
until the odometer appears in the information display area.
- Press and hold the SET button or SET switch until
the units change.
